{"title":"Connectors \u0026 Wiring Supplies","description":"\u003cp\u003eConnectors, D-sub pins and shells, terminals, aircraft wire and wiring harnesses. Brands include TE Connectivity, Amphenol RF, Sumitomo, Garmin and Dynon.\u003c\/p\u003e\u003cp\u003eConnectors are listed by P\/N. A quote needs the connector P\/N or the unit it plugs into.\u003c\/p\u003e","products":[{"product_id":"bendixking-ka-33","title":"BendixKing KA 33 Avionics Cooling Blower","description":"\u003cp\u003eBendixKing KA 33 is a cooling blower for panel-mounted avionics stacks of three or more units. It draws air from inside the aircraft and feeds it through flexible ducts to the rear of each unit, so it cools during ground operation as well and works in pressurized and non-pressurized aircraft. BendixKing requires a KA 33 or an equivalent cooling system for a full IFR installation of panel-mounted avionics; ram-air cooling is not accepted.\u003c\/p\u003e\u003cp\u003eP\/N 071-4037-01, in current numbering 071-04037-0001, is the 28 V version with six ports. It draws 0.5 A, delivers a total of 27 ±3 CFM through six ducts and needs a 1 A circuit breaker. It measures 134 × 175 × 102 mm and weighs 0.57 kg. The 14 V six-port version is 071-4037-00, the 28 V two-port version 071-4037-02.\u003c\/p\u003e\u003cp\u003eThe blower is mounted behind the instrument panel on the firewall, the side fuselage or a separate bracket, with the outlets towards the stack, at most 36 in (91 cm) from it and with at least 25 mm free at the air intake. No mounting holes are drilled in a pressurized airframe. P\/N 071-04037-0001 is offered new, 071-4037-01 serviceable\/overhauled. Fit depends on the P\/N and the aircraft type.\u003c\/p\u003e","brand":"BendixKing","offers":[{"title":"071-04037-0001 \/ New","offer_id":58181266637131,"sku":"071-04037-0001","price":31195.2,"currency_code":"CZK","in_stock":true},{"title":"071-4037-01 \/ Serviceable \/ Overhauled","offer_id":58181266669899,"sku":"071-4037-01-SV","price":0.0,"currency_code":"CZK","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1055\/1063\/3803\/files\/071-04037-0001.jpg?v=1791620123"},{"product_id":"te-connectivity-w31","title":"TE Connectivity W31","description":null,"brand":"TE Connectivity","offers":[{"title":"1 A","offer_id":58181514363211,"sku":"W31X2M1G1","price":1000.8,"currency_code":"CZK","in_stock":true},{"title":"10 A","offer_id":58181514395979,"sku":"W31X2M1G10","price":1140.5,"currency_code":"CZK","in_stock":true},{"title":"15 A","offer_id":58181514428747,"sku":"W31X2M1G15","price":1303.2,"currency_code":"CZK","in_stock":true},{"title":"2 A","offer_id":58181514461515,"sku":"W31X2M1G2","price":0.0,"currency_code":"CZK","in_stock":true},{"title":"3 A","offer_id":58181514494283,"sku":"W31X2M1G3","price":1432.5,"currency_code":"CZK","in_stock":true},{"title":"5 A","offer_id":58181514527051,"sku":"W31X2M1G5","price":1249.0,"currency_code":"CZK","in_stock":true},{"title":"7,5 A","offer_id":58181514559819,"sku":"W31X2M1G7.5","price":1503.4,"currency_code":"CZK","in_stock":true}]},{"product_id":"te-connectivity-w58","title":"TE Connectivity W58","description":null,"brand":"TE Connectivity","offers":[{"title":"1 A","offer_id":58181515477323,"sku":"W58XC4C12A1","price":0.0,"currency_code":"CZK","in_stock":true},{"title":"15 A","offer_id":58181515510091,"sku":"W58XC4C12A15","price":556.7,"currency_code":"CZK","in_stock":true},{"title":"20 A","offer_id":58181515542859,"sku":"W58XC4C12A20","price":289.8,"currency_code":"CZK","in_stock":true},{"title":"3 A","offer_id":58181515575627,"sku":"W58XC4C12A3","price":567.1,"currency_code":"CZK","in_stock":true},{"title":"5 A","offer_id":58181515608395,"sku":"W58XC4C12A5","price":569.86,"currency_code":"CZK","in_stock":true}]},{"product_id":"garmin-011-01364-10","title":"Garmin 011-01364-10 QMA Right Angle Connector Kit, 4 Pieces, for GTS 8XX","description":"\u003cp\u003eGarmin 011-01364-10 is a kit of four right-angle QMA connectors (Garmin connector P\/N 330-00500-10) for making the coaxial cable assemblies of the Garmin GTS 8XX traffic systems from M17\/128-RG400 or M17\/60-RG142 cable. Garmin lists the kit in the installation manuals of the GTS 800, GTS 820 and GTS 850 and of the GTS 825 and GTS 855. It is the helicopter\/fixed-wing version that Garmin requires in all helicopter applications and recommends for future fixed-wing installations; it replaces the fixed-wing kit 011-01364-00, which Garmin is phasing out. The straight version is 011-01364-11.\u003c\/p\u003e\u003cp\u003eA GTS 800 with one GA 58 antenna 011-01346-00 needs two four-piece kits, or one kit with the TNC-connector antenna 011-01346-02; a GTS 820 or GTS 850 needs two more kits for the GPA 65. Garmin states that QMA connectors other than those it specifies make the installation non-compliant. Garmin lists a kit weight of 0.08 kg. Fit depends on the GTS model and the antenna configuration.\u003c\/p\u003e","brand":"Garmin","offers":[{"title":"Default Title","offer_id":58181766676811,"sku":"011-01364-10","price":3753.18,"currency_code":"CZK","in_stock":true}]},{"product_id":"garmin-011-01364-11","title":"Garmin 011-01364-11 QMA Straight Connector Kit, 4 Pieces, for GTS 8XX","description":"\u003cp\u003eGarmin 011-01364-11 is a kit of four straight QMA connectors (Garmin connector P\/N 330-00500-11) for making the coaxial cable assemblies of the Garmin GTS 8XX traffic systems from M17\/128-RG400 or M17\/60-RG142 cable. Garmin lists the kit in the installation manuals of the GTS 800, GTS 820 and GTS 850 and of the GTS 825 and GTS 855. It is the helicopter\/fixed-wing version that Garmin requires in all helicopter applications and recommends for future fixed-wing installations; it replaces the fixed-wing kit 011-01364-01, which Garmin is phasing out. The right-angle version is 011-01364-10.\u003c\/p\u003e\u003cp\u003eA GTS 800 with one GA 58 antenna 011-01346-00 needs two four-piece kits, or one kit with the TNC-connector antenna 011-01346-02; a GTS 820 or GTS 850 needs two more kits for the GPA 65. Garmin states that QMA connectors other than those it specifies make the installation non-compliant. Garmin lists a kit weight of 0.05 kg. Fit depends on the GTS model and the antenna configuration.\u003c\/p\u003e","brand":"Garmin","offers":[{"title":"Default Title","offer_id":58181766709579,"sku":"011-01364-11","price":3753.18,"currency_code":"CZK","in_stock":true}]},{"product_id":"garmin-011-01364-14","title":"Garmin 011-01364-14 QMA Termination Connector Kit, 4 Pieces, for GTS 800\/820\/850","description":"\u003cp\u003eGarmin 011-01364-14 is a kit of four QMA 2-watt terminations for unused antenna ports on the Garmin GTS 800, GTS 820 and GTS 850 traffic systems. Garmin requires one kit in a single-antenna installation: without a bottom-mounted antenna, each of the four bottom jacks J1 BTM to J4 BTM is terminated. With a bottom monopole antenna on J1 BTM, the three-piece kit 011-01364-15 terminates J2 BTM to J4 BTM instead.\u003c\/p\u003e\u003cp\u003eThe kit belongs to the 011-01364-1x connector kits that Garmin requires in all helicopter applications and recommends for future fixed-wing installations; the earlier fixed-wing equivalent is 011-01364-04. Garmin lists a kit weight of 0.03 kg. Fit depends on the GTS model and the antenna configuration.\u003c\/p\u003e","brand":"Garmin","offers":[{"title":"Default Title","offer_id":58181767364939,"sku":"011-01364-14","price":4691.48,"currency_code":"CZK","in_stock":true}]},{"product_id":"garmin-011-01364-15","title":"Garmin 011-01364-15 QMA Termination Connector Kit, 3 Pieces, for GTS 800\/820\/850","description":"\u003cp\u003eGarmin 011-01364-15 is a kit of three QMA 2-watt terminations for unused bottom antenna jacks of the Garmin GTS 800, GTS 820 and GTS 850 traffic systems. Garmin requires one kit in a bottom monopole antenna installation: the monopole antenna connects to J1 BTM by a single coaxial cable, and the remaining jacks J2 BTM, J3 BTM and J4 BTM are terminated. Without a bottom antenna, the four-piece kit 011-01364-14 terminates all four bottom jacks instead.\u003c\/p\u003e\u003cp\u003eThe kit belongs to the 011-01364-1x connector kits that Garmin requires in all helicopter applications and recommends for future fixed-wing installations; the earlier fixed-wing equivalent is 011-01364-05. Garmin lists a weight of 0.03 kg for a QMA termination connector kit. Fit depends on the GTS model and the antenna configuration.\u003c\/p\u003e","brand":"Garmin","offers":[{"title":"Default Title","offer_id":58181767659851,"sku":"011-01364-15","price":3518.61,"currency_code":"CZK","in_stock":true}]},{"product_id":"031-320-rfx","title":"Amphenol RF 031-320-RFX BNC Male Straight Crimp Connector, RG-58","description":"\u003ch2\u003eAmphenol RF 031-320-RFX\u003c\/h2\u003e\u003cp\u003e50-ohm straight BNC male crimp connector for RG-58 cable — Part number 031-320-RFX.\u003c\/p\u003e\u003ch3\u003eHighlights\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e50-ohm straight BNC male crimp connector for RG-58 cable — Part number 031-320-RFX.\u003c\/li\u003e\n\u003cli\u003eExact identity: Amphenol RF 031-320-RFX\u003c\/li\u003e\n\u003cli\u003ePart number: 031-320-RFX\u003c\/li\u003e\n\u003cli\u003eVerify the exact part number, variant, approved equipment or aircraft eligibility, installation data and required interfaces before ordering.\u003c\/li\u003e\n\u003cli\u003eBNC plug\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eExact identity\u003c\/h3\u003e\u003cp\u003eAmphenol RF 031-320-RFX — 031-320-RFX.\u003c\/p\u003e\u003ch3\u003ePurpose and selection\u003c\/h3\u003e\u003cp\u003e50-ohm straight BNC male crimp connector for RG-58 cable\u003c\/p\u003e\u003ch3\u003eCompatibility and installation\u003c\/h3\u003e\u003cp\u003eVerify the exact part number, variant, approved equipment or aircraft eligibility, installation data and required interfaces before ordering.\u003c\/p\u003e","brand":"Amphenol","offers":[{"title":"Default Title","offer_id":58181875269963,"sku":"031-320-RFX","price":104.3,"currency_code":"CZK","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1055\/1063\/3803\/files\/031-320-RFX.jpg?v=1791629943"},{"product_id":"bendixking-050-02204-0000","title":"BendixKing 050-02204-0000 Installation Kit for KA 33 Cooling Blower","description":"\u003cp\u003e\u003cstrong\u003eBendixKing 050-02204-0000\u003c\/strong\u003e — This concise accessory card uses only the exact identity and facts supported by the sources below.\u003c\/p\u003e\u003cp\u003eProvides the specified function for KA 33 cooling blower: avionics installation kit.\u003c\/p\u003e\u003cp\u003eSix-port kit for 0.625-inch outside-diameter duct; distinct from the two-port 1.0-inch kit 050-02204-0001.\u003c\/p\u003e\u003cp\u003eMatch the complete part number and verify the current installation or maintenance documentation before order.\u003c\/p\u003e","brand":"BendixKing","offers":[{"title":"Default Title","offer_id":58181887000907,"sku":"050-02204-0000","price":11117.8,"currency_code":"CZK","in_stock":true}]},{"product_id":"dynon-100830-000","title":"Dynon 100830-000 D-Sub 9-Pin Male Connector Kit","description":"\u003cp\u003eDynon D-sub 9-pin Male Connector Kit — D-sub connector kit. Field-assembly kit provides a male 9-pin D-sub connector and its specified hardware.\u003c\/p\u003e\u003ch3\u003eProduct details\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 100830-000\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eType:\u003c\/strong\u003e D-sub connector kit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eContents:\u003c\/strong\u003e Connector, pins, shell and thumbscrews\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBefore ordering or installation\u003c\/h3\u003e\u003cp\u003eMatch the exact part number, revision, connector and approved application before ordering or installation. Follow current manufacturer and aircraft data.\u003c\/p\u003e\u003cp\u003eOne Dynon D-sub 9-pin Male Connector Kit; parent equipment, mating hardware and installation materials are not included unless explicitly listed.\u003c\/p\u003e","brand":"Dynon","offers":[{"title":"Default Title","offer_id":58182184862027,"sku":"100830-000","price":614.4,"currency_code":"CZK","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1055\/1063\/3803\/files\/100830-000.jpg?v=1790590125"},{"product_id":"dynon-100830-002","title":"Dynon 100830-002 D-sub 25-Pin Male Connector Kit","description":"\u003cp\u003eDynon 100830-002 is a male 25-pin D-sub connector kit for wiring Dynon avionics. The kit contains the connector, the pins, the connector shell and a thumb-screw set. The female 25-pin counterpart is Dynon 100831-002; the male 9-pin kit is 100830-000.\u003c\/p\u003e\u003cp\u003eDynon Certified, Dynon’s line for certified aircraft, does not list this P\/N.\u003c\/p\u003e","brand":"Dynon","offers":[{"title":"Default Title","offer_id":58182185124171,"sku":"100830-002","price":859.7,"currency_code":"CZK","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1055\/1063\/3803\/files\/100830-002.jpg?v=1790590128"},{"product_id":"dynon-100831-000","title":"Dynon 100831-000 Female 9-Pin D-Sub Connector Kit","description":"\u003ch2\u003eDynon female D-sub connector kit\u003c\/h2\u003e\u003cp\u003eFemale 9-pin D-sub connector kit with connector, pins, shell and thumb-screw set. Part number: 100831-000.\u003c\/p\u003e\u003ch3\u003eHighlights\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFemale 9-pin D-sub connector kit with connector, pins, shell and thumb-screw set.\u003c\/li\u003e\n\u003cli\u003eExact identity: Dynon female D-sub connector kit\u003c\/li\u003e\n\u003cli\u003ePart number: 100831-000\u003c\/li\u003e\n\u003cli\u003efemale D-sub\u003c\/li\u003e\n\u003cli\u003e9 pins\u003c\/li\u003e\n\u003cli\u003econnector shell and thumb screws included\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eExact identity\u003c\/h3\u003e\u003cp\u003eDynon female D-sub connector kit — Part number 100831-000.\u003c\/p\u003e\u003ch3\u003ePurpose and selection\u003c\/h3\u003e\u003cp\u003eFemale 9-pin D-sub connector kit with connector, pins, shell and thumb-screw set.\u003c\/p\u003e\u003ch3\u003eCompatibility and installation\u003c\/h3\u003e\u003cp\u003eVerify the exact part number, parent equipment, installation eligibility, connector and required interfaces against current approved data before ordering.\u003c\/p\u003e","brand":"Dynon","offers":[{"title":"Default Title","offer_id":58182185288011,"sku":"100831-000","price":614.4,"currency_code":"CZK","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1055\/1063\/3803\/files\/100831-000.jpg?v=1790590132"},{"product_id":"dynon-100831-001","title":"Dynon 100831-001 D-Sub Connector Kit, 15-Pin Female","description":"\u003cp\u003eDynon D-sub 15-pin Female Connector Kit — D-sub connector kit. Field-assembly kit provides a female 15-pin D-sub connector and its specified hardware.\u003c\/p\u003e\u003ch3\u003eProduct details\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 100831-001\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eType:\u003c\/strong\u003e D-sub connector kit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eContents:\u003c\/strong\u003e Connector, pins, shell and thumbscrews\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBefore ordering or installation\u003c\/h3\u003e\u003cp\u003eMatch the exact part number, revision, connector and approved application before ordering or installation. Follow current manufacturer and aircraft data.\u003c\/p\u003e\u003cp\u003eOne Dynon D-sub 15-pin Female Connector Kit; parent equipment, mating hardware and installation materials are not included unless explicitly listed.\u003c\/p\u003e","brand":"Dynon","offers":[{"title":"Default Title","offer_id":58182185615691,"sku":"100831-001","price":614.4,"currency_code":"CZK","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1055\/1063\/3803\/files\/100831-001.jpg?v=1790590136"},{"product_id":"dynon-100831-002","title":"Dynon 100831-002 D-sub 25-pin Female Connector Kit","description":"\u003cp\u003eDynon 100831-002 is a female 25-pin D-sub connector kit for building or repairing harnesses in a Dynon installation. The kit contains the connector, pins, connector shell and a thumb-screw set. Dynon lists it with its system cables, harnesses and connectors; the male 25-pin kit is P\/N 100830-002, and the female 9-pin and 15-pin kits are 100831-000 and 100831-001.\u003c\/p\u003e\u003cp\u003eA self-made D25F harness is one of the options Dynon gives, for example, for the SV-INTERCOM-2S, which has a D25M connector. Dynon sells the kit in its experimental product line, which is not intended for type-certificated aircraft.\u003c\/p\u003e","brand":"Dynon","offers":[{"title":"Default Title","offer_id":58182185746763,"sku":"100831-002","price":859.7,"currency_code":"CZK","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1055\/1063\/3803\/files\/100831-002.jpg?v=1790590139"},{"product_id":"mil-t-43435b-type-i","title":"Breyden Products 101-2BLK Waxed Nylon Lacing Tape, MIL-T-43435B Type I","description":"\u003cp\u003eBreyden Products 101-2BLK is a black flat-braided lacing tape of high-tenacity continuous-filament nylon, impregnated with a microcrystalline fungicidal wax that improves knot holding. Breyden lists 101-2 as formerly MIL-T-43435B Type I, Size 1, Finish B, now A-A-52080-B-1. The tape is 0.180–0.220 in wide and 0.013–0.019 in thick, with a minimum tensile strength of 135 lb, maximum elongation of 40 % and a temperature range of −55 to +121 °C. The spool holds 250 yd (229 m).\u003c\/p\u003e\u003cp\u003eMIL-T-43435B covers flat-braided tapes for lacing and tying, requires finishes free of copper and mercury and suitable for contact with insulated wire, and was cancelled in favour of A-A-52080 to A-A-52084.\u003c\/p\u003e","brand":"Breyden Products","offers":[{"title":"Default Title","offer_id":58182186664267,"sku":"101-2BLK","price":2527.1,"currency_code":"CZK","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1055\/1063\/3803\/files\/101-2BLK.jpg?v=1790591856"},{"product_id":"203540-1","title":"TE Connectivity 203540-1 AMP M Series 14-Position Plug Connector","description":"\u003cp\u003eTE Connectivity 203540-1 is a 14-position AMP M Series plug connector assembly for cable-to-panel connections, with pin contacts in three rows at 3.81 mm (.150 in) centerline. TE specifies gold-plated contacts (0.76 µm) rated 13 A maximum for wire from 30 to 14 AWG (0.05–2 mm²), a 250 V AC rating and an operating range of −55 to +150 °C for power and signal circuits.\u003c\/p\u003e\u003cp\u003eThe assembly is screw-mounted and measures 31.75 × 15.75 × 12.5 mm. Fit depends on the mating connector.\u003c\/p\u003e","brand":"TE Connectivity","offers":[{"title":"Default Title","offer_id":58182417645899,"sku":"203540-1","price":1855.7,"currency_code":"CZK","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1055\/1063\/3803\/files\/203540-1.jpg?v=1790925920"},{"product_id":"205204-9","title":"TE Connectivity 205204-9 AMPLIMITE HDP-20 9-Position D-Sub Plug Housing","description":"\u003cp\u003eTE Connectivity 205204-9 is a 9-position D-sub plug housing of the AMPLIMITE HDP-20 series, shell size 1, for cable-to-cable connections in signal circuits. It takes size 20 crimp contacts on a 2.74 mm (.108 in) centerline; the contacts are ordered separately.\u003c\/p\u003e\u003cp\u003eThe shell is zinc-plated steel and provides shielding, the insert is thermoplastic rated UL 94V-0, and the housing is unsealed. TE gives an operating range of −55 to +105 °C.\u003c\/p\u003e","brand":"TE Connectivity","offers":[{"title":"Default Title","offer_id":58182418039115,"sku":"205204-9","price":79.2,"currency_code":"CZK","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1055\/1063\/3803\/files\/205204-9.jpg?v=1790925925"},{"product_id":"205842-1","title":"TE Connectivity 205842-1 AMP CPC Series 2 63-Position Plug Housing","description":"\u003cp\u003eTE Connectivity 205842-1 is a 63-position plug housing of the AMP Circular Plastic Connector (CPC) Series 2 for free-hanging wire-to-wire connections. The black all-plastic thermoplastic housing (UL 94V-0) has shell size 23 with the 23-63 insert and takes socket contacts; TE rates the contacts at 7.5 A maximum and the connector at 250 V AC\/DC, with an operating range of −55 to +105 °C. Mating is keyed and held by a threaded coupling nut, 1-3\/8-18 UNEF-2A.\u003c\/p\u003e\u003cp\u003eThe housing is unsealed and unshielded and is intended for signal circuits, with wire insulation of 1.73 mm (.068 in) diameter. The crimp socket contacts (size 20) are ordered separately.\u003c\/p\u003e","brand":"TE Connectivity","offers":[{"title":"Default Title","offer_id":58182427672907,"sku":"205842-1","price":485.8,"currency_code":"CZK","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1055\/1063\/3803\/files\/205842-1.jpg?v=1790925932"},{"product_id":"205843-1","title":"TE Connectivity 205843-1 AMP CPC Series 2 Receptacle Housing, 63 Positions","description":"\u003cp\u003eTE Connectivity 205843-1 is a 63-position receptacle housing from the AMP Circular Plastic Connectors (CPC) Series 2, shell size 23 (insert arrangement 23-63), for wire-to-panel connections. It takes pin contacts, which are not included, and mounts to the panel with a flange and mounting holes. The threaded coupling (1-3\/8-18 UNEF-2A) is keyed for mating alignment.\u003c\/p\u003e\u003cp\u003eTE specifies a black thermoplastic housing rated UL 94V-0, 250 V AC\/DC, a maximum contact current of 7.5 A and an operating range of −55 to +105 °C. Fit depends on the mating plug and contact P\/Ns.\u003c\/p\u003e","brand":"TE Connectivity","offers":[{"title":"Default Title","offer_id":58182443630923,"sku":"205843-1","price":573.4,"currency_code":"CZK","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1055\/1063\/3803\/files\/205843-1.jpg?v=1791630286"},{"product_id":"safe-328","title":"Sandia SAFE 328","description":"\u003cp\u003eSandia Aerospace SAFE 328 (P\/N 305467-00) is a three-port avionics cooling blower for 28 V DC aircraft with a fan-fail output. It delivers up to 20 CFM across all ports without static pressure, runs on 22–31 V DC at 0.40 A nominal and 0.55 A at start-up, and measures 142 × 121 × 32 mm at 0.32 kg.\u003c\/p\u003e\u003cp\u003eOne blower cools up to three avionics units through ducts; unused ports are capped. The Fan Fail pin stays low in normal operation and goes high when airflow drops to 65 % of nominal, sensed from motor RPM, so the connected avionics register the loss of cooling; an external pull-up is required. Power comes from the aircraft bus through a 1 A fuse or breaker, or from the cooled unit if it has a suitable output.\u003c\/p\u003e\u003cp\u003eThe fan mounts with three #6 or #8 screws, and the air is ducted with aircraft-approved tubing. It ships with the mating connector housing fitted and crimp contacts. Sandia holds FAA-PMA approval PQ0894SW for the Diamond DA40; a US PMA is not automatic EASA approval, so a certified installation needs approved data for the aircraft type and a Certificate of Release to Service. Fit depends on the aircraft type and the avionics to be cooled.\u003c\/p\u003e","brand":"Sandia Aerospace","offers":[{"title":"Default Title","offer_id":58182627328331,"sku":"305467-00","price":13476.0,"currency_code":"CZK","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1055\/1063\/3803\/files\/305467-00.jpg?v=1790587995"},{"product_id":"safe-128","title":"Sandia SAFE 128","description":"\u003cp\u003eSandia Aerospace SAFE 128 (P\/N 305468-00) is an axial avionics cooling fan with a fan-fail output that attaches directly to the cooling port of an avionics unit. It delivers a nominal 20 CFM without load, runs on 22–31 V DC at 0.10 A nominal and below 0.25 A at start-up, and measures 60 × 73 × 37 mm including pins at 0.11 kg.\u003c\/p\u003e\u003cp\u003eThe Fan Fail pin stays low in normal operation and goes high when airflow drops to 60 % of nominal, sensed from fan RPM, so the connected avionics register the loss of cooling; an external pull-up is required. Power comes from the aircraft bus through a 0.5 A fuse or breaker, or from the cooled unit if it has a suitable output.\u003c\/p\u003e\u003cp\u003eThe fan mounts with four #6-32 or #8-32 screws, not supplied; the airflow direction must be observed. Installation kit 305477-00 with mating connector 305479-03 and four contacts, is supplied. Sandia holds FAA-PMA approval PQ0894SW for the Diamond DA40; a US PMA is not automatic EASA approval, so a certified installation needs approved data for the aircraft type and a Certificate of Release to Service. Fit depends on the aircraft type and the avionics unit to be cooled.\u003c\/p\u003e","brand":"Sandia Aerospace","offers":[{"title":"Default Title","offer_id":58182627361099,"sku":"305468-00","price":7506.36,"currency_code":"CZK","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1055\/1063\/3803\/files\/305468-00.jpg?v=1790587998"},{"product_id":"safe-528","title":"Sandia SAFE 528","description":"\u003cp\u003eSandia Aerospace SAFE 528 (P\/N 305722-00) is an avionics cooling blower for 28 V DC aircraft that cools up to five avionics units and has a fan-fail output. It delivers 20 CFM across all ports without static pressure, runs on 22–31 V DC at 0.40 A nominal and 0.55 A at start-up, and measures 53 × 130 × 171 mm at 0.54 kg.\u003c\/p\u003e\u003cp\u003eThe Fan Fail pin goes high when airflow drops to 65 % of nominal, sensed from fan RPM, so the connected avionics register the loss of cooling; an external pull-up is required. Power comes from the aircraft bus through a 1 A fuse or breaker, or from the cooled unit if it has a suitable output. The blower is rated for −20 to +55 °C and 55,000 ft.\u003c\/p\u003e\u003cp\u003eIt mounts with three or six #6-32 or #8-32 screws, not supplied, and the air is ducted with aircraft-approved tubing; unused ports are capped. Sandia's complete system 705722-00 adds installation kit 305477-00 with mating connector 305479-03. Sandia states FAA-PMA approval; a US PMA is not automatic EASA approval, so a certified installation needs approved data for the aircraft type and a Certificate of Release to Service. Fit depends on the aircraft type, the avionics to be cooled and whether kit 305477-00 is required.\u003c\/p\u003e","brand":"Sandia Aerospace","offers":[{"title":"Default Title","offer_id":58182627393867,"sku":"305722-00","price":15638.3,"currency_code":"CZK","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1055\/1063\/3803\/files\/305722-00.jpg?v=1792264750"},{"product_id":"4-50-141-1","title":"TED 4-50-141-1 BNC Coaxial Connector","description":null,"brand":"TED Manufacturing","offers":[{"title":"Default Title","offer_id":58182646464843,"sku":"4-50-141-1","price":4253.6,"currency_code":"CZK","in_stock":true}]},{"product_id":"5-10-43-2","title":"TED Manufacturing 5-10-43-2 TNC Connector for RG 393 Cable","description":"\u003cp\u003eTED Manufacturing 5-10-43-2 is a straight TNC cable plug for RG 393\/U coaxial cable. Honeywell lists it as the vendor part for its straight TNC connector 030-00108-0004 on RG 393, the preferred antenna cable in the KRA 405B radar altimeter installation manual, and the KRA 405 manual names it for the connectors of the KA 54A antenna installation kit. The right-angle counterpart in the same table is TED 5-30-14-1.\u003c\/p\u003e\u003cp\u003eHoneywell notes that radar altimeter performance depends on the VSWR of the antenna cable, so the connector must be assembled to the cable exactly to the installation manual.\u003c\/p\u003e","brand":"TED Manufacturing","offers":[{"title":"Default Title","offer_id":58182751551819,"sku":"5-10-43-2","price":5692.01,"currency_code":"CZK","in_stock":true}]},{"product_id":"5205208-1","title":"TE Connectivity 5205208-1 AMPLIMITE HDP-20 25-Position D-Sub Plug","description":"\u003cp\u003eTE Connectivity 5205208-1 is a 25-position AMPLIMITE HDP-20 D-sub plug in shell size 3 for cable-to-cable connections, with panel mounting holes. It takes size 20 crimp contacts, which are ordered separately. The full metal shell is zinc-plated steel and shielded; the insert is glass-filled PBT\/nylon rated UL 94V-0. TE specifies an operating range of −55 to +105 °C for signal circuits.\u003c\/p\u003e\u003cp\u003eThe right version depends on whether the size 20 crimp contacts are also required.\u003c\/p\u003e","brand":"TE Connectivity","offers":[{"title":"Default Title","offer_id":58182766526795,"sku":"5205208-1","price":116.8,"currency_code":"CZK","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1055\/1063\/3803\/files\/5205208-1.jpg?v=1791672406"},{"product_id":"9-30-10","title":"TED Manufacturing 9-30-10 Tray Mount RF Connector","description":"\u003cp\u003eTED Manufacturing 9-30-10 is a blind-mating, self-centering RF antenna connector for tray-mounted equipment. As the unit is pushed into the panel, the connector aligns and centres itself with its mating connector, so the RF connection is made without rear access to the panel. Fit depends on the equipment the connector is for.\u003c\/p\u003e","brand":"TED Manufacturing","offers":[{"title":"Default Title","offer_id":58183985529163,"sku":"9-30-10","price":1107.2,"currency_code":"CZK","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1055\/1063\/3803\/files\/209-9-30-10.jpg?v=1791814777"},{"product_id":"9020-17008-01","title":"L3Harris 9020-17008-01","description":"\u003cp\u003eAcron Aviation 9020-17008-01 is a short pre-fabricated coaxial cable assembly for the Lynx NGT-9000, with a straight size 8 plug on one end and a TNC jack on the other. The Lynx installation manual lists these assemblies for the L-band and GPS antenna cabling. The assembly is 8.00 ± 0.50 in (about 203 mm) long, with a maximum loss of 0.50 dB and a maximum VSWR of 1.5:1.\u003c\/p\u003e\u003cp\u003eOne 9020-17008-01 is part of the straight-connector installation kits 9060-17000-01 (panel mount) and 9060-17500-01 (remote mount). The NGT-9000+ and NGT-9000D+ need three additional pigtail assemblies for the active traffic directional antenna and the NGT-9000D one for the upper L-band antenna; the number depends on the installation configuration. The BNC and right-angle versions are 9020-17009-01, 9020-17010-01 and 9020-17011-01. Fit depends on the transponder model.\u003c\/p\u003e","brand":"Acron Aviation","offers":[{"title":"Default Title","offer_id":58183989297483,"sku":"9020-17008-01","price":3706.27,"currency_code":"CZK","in_stock":true}]},{"product_id":"acf-314","title":"Sandia ACF 314","description":"\u003cp\u003eSandia Aerospace ACF 314 is a three-port avionics cooling fan for 14 V DC aircraft that cools up to three avionics units at the same time. Its brushless blower delivers up to 20 CFM of cooling air and draws 960 mA, 1.7 A at start-up. The unit measures 5.92 × 5.18 × 2.10 in (150 × 132 × 53 mm) including the mounting flange and weighs 1.18 lb (0.54 kg).\u003c\/p\u003e\u003cp\u003ePower is connected through a 3-pin Molex connector: on the ACF 314, pin 3 is aircraft positive, pin 2 ground and pin 1 not connected. Sandia supplies a connector kit with the unit; the mating parts are housing 03-09-1032 and crimp contacts 02-09-1119. The fan is qualified to RTCA DO-160C and rated for −20 to +55 °C and 50,000 ft. It has no fan-fail output; the SAFE 328 is the Sandia three-port fan with fault detection, and the ACF 328 is the 28 V version.\u003c\/p\u003e\u003cp\u003eSandia holds FAA-PMA approval PQ0894SW for the ACF series; a US PMA is not automatic EASA approval, so a certified installation needs approved data for the aircraft type and a Certificate of Release to Service. Fit depends on the aircraft type and the avionics to be cooled.\u003c\/p\u003e","brand":"Sandia Aerospace","offers":[{"title":"Default Title","offer_id":58184162705739,"sku":"ACF314","price":9026.4,"currency_code":"CZK","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1055\/1063\/3803\/files\/ACF314.jpg?v=1790591475"},{"product_id":"dba-600","title":"Deklin DBA-600 BNC Tray Connector","description":"\u003cp\u003eDeklin DBA-600 is a BNC tray connector that is installed in an avionics mounting tray in place of the solder-type RF tray connector. It is designed for Bendix\/King Silver Crown trays and other trays that use the solder-type connector, so the antenna coax connects to a BNC jack on the tray instead of being soldered.\u003c\/p\u003e\u003cp\u003eThe connector has a precision nickel body and a gold-plated center conductor, and it is held in the tray with a snap ring. Fit depends on the radio or transponder tray type.\u003c\/p\u003e","brand":"Deklin","offers":[{"title":"Default Title","offer_id":58184547959115,"sku":"DBA-600","price":1094.7,"currency_code":"CZK","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1055\/1063\/3803\/files\/DBA-600.jpg?v=1791715816"},{"product_id":"m83519-1-2","title":"M83519\/1-2 Solder Sleeve Shield Terminator","description":"\u003cp\u003eM83519\/1-2 is an insulated, heat-shrinkable solder sleeve shield terminator without a lead wire, defined by military specification sheet MIL-S-83519\/1 for cables with tin- or silver-plated shields (Class I). The -2 size takes cables up to 0.145 in (3.68 mm) in diameter with a shield diameter of at least 0.055 in (1.40 mm); the sleeve is 0.650 ± 0.07 in (16.5 mm) long. The temperature rating is −55 to +150 °C.\u003c\/p\u003e\u003cp\u003eThe transparent polyvinylidene fluoride (PVDF) sleeve contains a fluxed Sn63 solder preform. The specification gives environmental resistance on cables with MIL-C-27500 jacket types 05, 08, 09, 10, 11, 12, 14, 15 and 23 and on MIL-C-7078 cables. M83519\/1-2 supersedes NAS1744-2, NAS1745-2, NAS1745-14, NAS1746-2, M81786\/7-1, M81786\/8-1. MIL-S-83519\/1 is superseded by SAE AS83519\/1.\u003c\/p\u003e","brand":"Sumitomo","offers":[{"title":"Default Title","offer_id":58184683651403,"sku":"H-M-2","price":43.8,"currency_code":"CZK","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1055\/1063\/3803\/files\/H-M-2.jpg?v=1792264904"},{"product_id":"m83519-1-3","title":"M83519\/1-3 Solder Sleeve Shield Terminator","description":"\u003cp\u003eM83519\/1-3 is an insulated, heat-shrinkable solder sleeve shield terminator without a lead wire, defined by military specification sheet MIL-S-83519\/1 for cables with tin- or silver-plated shields (Class I). The -3 size takes cables up to 0.200 in (5.08 mm) in diameter with a shield diameter of at least 0.085 in (2.16 mm); the sleeve is 0.650 ± 0.07 in (16.5 mm) long. The temperature rating is −55 to +150 °C.\u003c\/p\u003e\u003cp\u003eThe transparent polyvinylidene fluoride (PVDF) sleeve contains a fluxed Sn63 solder preform. The specification gives environmental resistance on cables with MIL-C-27500 jacket types 05, 08, 09, 10, 11, 12, 14, 15 and 23 and on MIL-C-7078 cables. M83519\/1-3 supersedes NAS1744-3, NAS1745-3, NAS1745-15, NAS1746-3, M81786\/7-2, M81786\/8-2. MIL-S-83519\/1 is superseded by SAE AS83519\/1.\u003c\/p\u003e","brand":"Sumitomo","offers":[{"title":"Default Title","offer_id":58184684142923,"sku":"H-M-3","price":43.8,"currency_code":"CZK","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1055\/1063\/3803\/files\/H-M-3.jpg?v=1792264907"},{"product_id":"m83519-1-5","title":"M83519\/1-5 Solder Sleeve Shield Terminator","description":"\u003cp\u003eM83519\/1-5 is an insulated, heat-shrinkable solder sleeve shield terminator without a lead wire, defined by military specification sheet MIL-S-83519\/1 for cables with tin- or silver-plated shields (Class I). The -5 size takes cables up to 0.300 in (7.62 mm) in diameter with a shield diameter of at least 0.170 in (4.32 mm); the sleeve is 0.750 ± 0.07 in (19.1 mm) long. The temperature rating is −55 to +150 °C.\u003c\/p\u003e\u003cp\u003eThe transparent polyvinylidene fluoride (PVDF) sleeve contains a fluxed Sn63 solder preform. The specification gives environmental resistance on cables with MIL-C-27500 jacket types 05, 08, 09, 10, 11, 12, 14, 15 and 23 and on MIL-C-7078 cables. M83519\/1-5 supersedes NAS1744-4, NAS1745-4, NAS1745-16, NAS1746-4, M81786\/7-3, M81786\/8-3. MIL-S-83519\/1 is superseded by SAE AS83519\/1.\u003c\/p\u003e","brand":"Sumitomo","offers":[{"title":"Default Title","offer_id":58184684634443,"sku":"H-M-5","price":50.0,"currency_code":"CZK","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1055\/1063\/3803\/files\/H-M-5.jpg?v=1792264910"},{"product_id":"m83519-2-7","title":"M83519\/2-7 Solder Sleeve Shield Terminator with 22 AWG Lead","description":"\u003cp\u003eM83519\/2-7 is an insulated, heat-shrinkable solder sleeve shield terminator with a preinstalled M22759\/32-22 lead wire (22 AWG), defined by military specification sheet MIL-S-83519\/2 for cables with tin- or silver-plated shields (Class I). The -7 size takes cables up to 0.145 in (3.68 mm) in diameter with a shield diameter of at least 0.055 in (1.40 mm); the sleeve is 0.650 ± 0.07 in (16.5 mm) long and the lead at least 6.00 in (152 mm). The temperature rating is −55 to +150 °C.\u003c\/p\u003e\u003cp\u003eThe transparent polyvinylidene fluoride (PVDF) sleeve contains a fluxed Sn63 solder preform and a thermal indicator that turns colorless on termination. The specification gives environmental resistance on cables with MIL-C-27500 jacket types 05, 08, 09, 10, 11, 12, 14, 15 and 23 and on MIL-C-7078 cables. MIL-S-83519\/2 is superseded by SAE AS83519\/2.\u003c\/p\u003e","brand":"Sumitomo","offers":[{"title":"Default Title","offer_id":58184705769803,"sku":"HML-7","price":58.4,"currency_code":"CZK","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1055\/1063\/3803\/files\/HML-7.jpg?v=1792264913"},{"product_id":"m83519-2-8","title":"M83519\/2-8 Solder Sleeve Shield Terminator with 22 AWG Lead","description":"\u003cp\u003eM83519\/2-8 is an insulated, heat-shrinkable solder sleeve shield terminator with a preinstalled M22759\/32-22 lead wire (22 AWG), defined by military specification sheet MIL-S-83519\/2 for cables with tin- or silver-plated shields (Class I). The -8 size takes cables up to 0.200 in (5.08 mm) in diameter with a shield diameter of at least 0.085 in (2.16 mm); the sleeve is 0.650 ± 0.07 in (16.5 mm) long and the lead at least 6.00 in (152 mm). The temperature rating is −55 to +150 °C.\u003c\/p\u003e\u003cp\u003eThe transparent polyvinylidene fluoride (PVDF) sleeve contains a fluxed Sn63 solder preform and a thermal indicator that turns colorless on termination. The specification gives environmental resistance on cables with MIL-C-27500 jacket types 05, 08, 09, 10, 11, 12, 14, 15 and 23 and on MIL-C-7078 cables. MIL-S-83519\/2 is superseded by SAE AS83519\/2.\u003c\/p\u003e","brand":"Sumitomo","offers":[{"title":"Default Title","offer_id":58184706818379,"sku":"HML-8","price":60.5,"currency_code":"CZK","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1055\/1063\/3803\/files\/HML-8.jpg?v=1792264916"},{"product_id":"tcw-tech-ifc-harn","title":"TCW Technologies IFC-HARN Wiring Harness, for Intelligent Flap Controller IFC-10","description":"\u003cp\u003eTCW Technologies IFC-HARN is the wiring harness for the TCW Intelligent Flap Controller IFC-10, the controller that drives DC motor flap actuators such as the Van's Aircraft actuators in RV homebuilt aircraft. The harness is 8 ft (about 2.4 m) long, colour coded and made with Mil-spec wire and connector terminations. The IFC-10 installation instructions name it as the compatible harness, model IFC-10-Harn.\u003c\/p\u003e\u003cp\u003eThe leads follow the IFC-10 wiring diagram: white #20 to aircraft power through a 7.5 A fuse or circuit breaker, black #20 to ground, red and green #20 to the flap motor, blue and violet #22 to the pilot flap switch, orange and yellow #22 to the co-pilot switch, and white\/black #22 to the optional ASW-1 airspeed switch. TCW states that the IFC is not TSO'd and is for aircraft certified in the Experimental category only; the installer is responsible for the suitability of the installation.\u003c\/p\u003e","brand":"TCW Technologies","offers":[{"title":"Default Title","offer_id":58184732016971,"sku":"IFC-Harn","price":2016.3,"currency_code":"CZK","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1055\/1063\/3803\/files\/IFC-Harn.jpg?v=1790591483"},{"product_id":"amphenol-ms3106a-10sl-3s","title":"Amphenol Industrial MS3106A-10SL-3S Mating Plug for RC Allen RCA56","description":"\u003cp\u003eMS3106A-10SL-3S is a MIL-DTL-5015 circular connector plug to standard sheet MS3106: a straight AN-type plug with threaded coupling and solder contacts. The part number codes class A (solid shell), shell size 10SL, insert arrangement 10SL-3 with three size 16 contacts, and socket contacts (S). Kelly Manufacturing lists MS3106A10SL-3S as the mating connector of the RC Allen RCA56 series electric turn and bank indicators (RCA56-3B, -3BL, -3W and -3WL), whose connector carries +11 to 30 V DC on pin A, ground on pin B and a spare on pin C; the RC Allen tachometers list the MS3106-10SL-3S connector.\u003c\/p\u003e\u003cp\u003eMIL-DTL-5015 and sheet MS3106 were cancelled on 23 December 2009 and replaced by SAE-AS50151 and SAE-AS31061; the RC Allen catalog of January 2026 still names this plug. Fit depends on the instrument model.\u003c\/p\u003e","brand":"Amphenol","offers":[{"title":"Default Title","offer_id":58187342086475,"sku":"MS3106A-10SL-3S","price":1278.2,"currency_code":"CZK","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1055\/1063\/3803\/files\/MS3106A-10SL-3S.jpg?v=1791706124"},{"product_id":"ms3126f22-55s","title":"Amphenol MS3126F22-55S MIL-DTL-26482 Circular Plug","description":"\u003cp\u003eMS3126F22-55S is a MIL-DTL-26482 Series 1 circular connector plug to standard sheet MS3126: a straight plug with bayonet coupling and crimp-type, front-release contacts. The part number codes class F (grommet seal with strain relief clamp, conductive), shell size 22, insert arrangement 22-55 to MIL-STD-1669 with 55 size 20 contacts of service rating I, socket contacts (S), normal insert position and the default finish W, olive drab cadmium plate. The shell and coupling ring are aluminium alloy; the bayonet pins are passivated stainless steel. The shop item is made by Amphenol.\u003c\/p\u003e\u003cp\u003eSeries 1 connectors are rated for −55 to +125 °C; the maximum working voltage for service rating I is 600 V AC rms at sea level and 300 V at 70,000 ft. The plug mates with MS3120, MS3122, MS3124, MS3127 and MS3128 receptacles. MS3126 has been inactive for new design since 5 September 1975; for new design the standard refers to MS3476, which uses rear-release contacts. The right version depends on whether the socket contacts are required.\u003c\/p\u003e","brand":"Amphenol","offers":[{"title":"Default Title","offer_id":58187342676299,"sku":"MS3126F22-55S","price":3268.39,"currency_code":"CZK","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1055\/1063\/3803\/files\/amphenol-ms3126f22-55s.jpg?v=1790531431"},{"product_id":"ms3476l24-61sz","title":"Amphenol RF MS3476L24-61SZ","description":"\u003cp\u003eMS3476L24-61SZ is a MIL-DTL-26482 Series 2 circular connector plug to specification sheet MS3476, with bayonet coupling and crimp-type contacts. The part number codes class L (fluid resistant, conductive electroless nickel finish), shell size 24, insert arrangement 24-61 to MIL-STD-1669 with 61 size 20 contacts of service rating I, socket contacts (S) and alternate insert position Z (324°). For the shell-size-24 socket plug MS3476 sets a maximum weight of 87 g without contacts and accessories.\u003c\/p\u003e\u003cp\u003eSeries 2 connectors are rated for −55 to +200 °C; the maximum working voltage for service rating I is 600 V AC rms at sea level and 300 V at 70,000 ft. The plug mates with MS3470, MS3471, MS3472, MS3474, MS3477 and MS3479 receptacles and, when both connectors carry a full complement of power contacts, with Series 1 receptacles such as MS3120, MS3122 and MS3124. It must be used with a backshell to SAE-AS85049, which is procured separately. MS3476 is approved for new and existing designs. The right version depends on whether the socket contacts are required.\u003c\/p\u003e","brand":"Amphenol","offers":[{"title":"Default Title","offer_id":58187342971211,"sku":"MS3476L24-61SZ","price":1142.6,"currency_code":"CZK","in_stock":true}]},{"product_id":"pe4047","title":"Pasternack PE4047 TNC Male Crimp Connector for RG142 \/ RG400","description":"\u003cp\u003ePasternack PE4047 is a straight 50 Ω TNC male connector with crimp attachment for RG55, RG142, RG223 and RG400 coaxial cable, for DC to 6 GHz with a maximum VSWR of 1.5:1. The interface complies with MIL-STD-348A and the coupling thread is 7\/16-28 UNEF.\u003c\/p\u003e\u003cp\u003eThe contact is gold-plated brass (30 µin minimum), the body, coupling nut and crimp sleeve are nickel-plated brass and the insulation is PTFE. The outer conductor is crimped with a 0.213 in (5.41 mm) hex die and the contact with a 0.068 in (1.73 mm) hex die. Operating voltage is 500 Vrms and operating temperature −65 to +165 °C. The connector is 27.86 mm long and 14.50 mm across and weighs 15 g.\u003c\/p\u003e","brand":"Pasternack","offers":[{"title":"Default Title","offer_id":58187373510987,"sku":"PE4047","price":944.6,"currency_code":"CZK","in_stock":true}]},{"product_id":"cygnet-aerospace-ca3934","title":"Cygnet Aerospace CA3934-12","description":"\u003cp\u003eCygnet Aerospace CA3934 is an FAA-PMA coil cord that connects control wheel switches to the instrument panel; the coiled section extends and contracts through the full control wheel travel. It is supplied as CA3934-12 with 12 conductors or CA3934-24 with 24 conductors, with 22 AWG wire to MIL-W-16878\/6 and fire-retardant construction to MIL-C-27072.\u003c\/p\u003e\u003cp\u003eCygnet holds the PMA for installation with Garmin autopilots, with eligibility per the Garmin AML. A US AML line is not automatic EASA approval: a certified aircraft needs an approved modification and a Certificate of Release to Service after installation. Fit depends on the conductor count and the aircraft type.\u003c\/p\u003e","brand":"Cygnet Aerospace","offers":[{"title":"12 Conductors","offer_id":58395162771787,"sku":"CA3934-12","price":8217.4,"currency_code":"CZK","in_stock":true},{"title":"24 Conductors","offer_id":58395162804555,"sku":"CA3934-24","price":9806.2,"currency_code":"CZK","in_stock":true}]}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1055\/1063\/3803\/collections\/category-parts-electrical-supplies.jpg?v=1791640545","url":"https:\/\/shop.airteam.eu\/collections\/parts-electrical-supplies.oembed","provider":"AIR TEAM","version":"1.0","type":"link"}